Media Library / Images

Hose assemblies for petroleum based products

Yellow Band quality with nozzle, TW coupling, flange connection

Rubber Expansion Joint ERV-W 80.16

WHITE BAND expansion joints for foodstuffs, also containing oil and fat. Liner corresponds to Recommendation XXI of BfR and FDA-21CFR 177.2600. Not approved for drinking water. Temperature range (depending on medium) - 20° C up to + 90° C, temporarily up to 100° C. Electrically non-conductive.

Ship loading/unloading various media - STW 150 and UTS 150 hose assemblies

Safety Swivel Break SSB 16 SS of stainless steel f. ZVA HV for AdBlue®

old design

Oasis SV Sandwich Valves 100series, for CNG

Adapters / couplers for vehicles fighting dangerous goods incidents:

Adapter for Rail Tanker 51/2" connection KWZ SS/Vi x VK 50 SS/Vi

SD 38 Pyropal

Steam hose with steel braids for wet saturated steam up to 18 bar (210° C) and hot water up to 120° C. For cold water up to 25 bar. Minimum burst pressure 180 bar (1 : 10 safety factor

Elaflon Plus FEP hose assembly with KSS anti kinking sleeve

flange hose fitting with special coating

ERV Rubber Expansion Joints

Picture 5

ROTEX 200.10 SS TAS

Rubber Expansion Joint with PTFE lining and PTFE vakuum support ring

Terminal / gantry: 'Polypal Oil 100' and 'TW 100' hose assemblies for bottom loading of road tankers

ERV-G

with vacuum support spiral

FWS 50 PTFE

Composite hose with PTFE lining

Oasis FV103 45° Fill Valve with NC 203 P36 Nozzle, for CNG

Nozzles and hose assemblies for the forecourt

ZVA Slimline 2, ZVA Slimline 2 GR, Slimline hose assemblies

Loading Brine (salt solutíon for winter service): CHS hose asssembly, DDC Dry Disconnect Coupling

ELAPHARM Type EPH

electrically isolating 'I', with blue cover, to EN 16820, Type A. FDA conform, homogeneous elastomer hose construction with smooth, white PTFE liner. Clamp fittings, lining flared (free of dead spaces).

Elaflex refuelling equipment:

Quality is in the detail.

DDC-V 50 F Aseptic

MannTek Dry Disconnect Coupling, DN 50, stainless steel, with Aseptic flange

ZH 50 nozzle with MK50SS + HD hose assembly, DDC-V 80 Ms with cap, MK 80 Ms with VB 80 P

Storz Safety Coupling SHK

upon uncoupling, the safety dust plug first falls into holding claws, relasing an eventual pressure within the system. Only then the dust cap can be fully taken off. - increased protection for the operating personnel. Easy to use, no additional pressure release necessary, slim design, does not build up, no freezing up in the dome section.

Hose Reel with hydraulic rewind system blue, TW 100, DDC-M 100

SC 50 SS

Spannloc clamps, stainless steel

UTS hose assembly with AMKC 25 SS/SS

'Camlock' stainless steel coupler to EN 14420 - 7 with hose tail and Spannloc stainless steel clamps

ELAFLEX Hamburg

Stock special flanges

VB 80 SSE

TW dust plug of stainless steel, surface in contact with the medium additionally coated with Teflon® PFA. This type is used if stainless steel does not have a sufficient chemical resistance (i.e. for hydrochloric acid and iron-III-chloride) and polypropylene is not possible because of insufficient stability. Available in all standard sizes.

L.P. Gas rail tanker

loading and unloading with DGC Dry Gas Couplings, LPG hose assemblies. Vehicle side: DGC-V male couplings with flange

ZVA Slimline 2

ELAPHARM Type EPH

electrically isolating 'I', with blue cover, to EN 16820, Type A. FDA conform, homogeneous elastomer hose construction with smooth, white PTFE liner. Clamp fittings, lining flared (free of dead spaces).

ERV-G Yellow Band rubber expansion joint, installation underneath a road tanker